2020.1.1500.2 MQTT

1 Overview
2 Where to find
3 Feature overview
4 How to use
5 Prerequisites for MQTT
6 Used Protocol
7 Supported Types
8 Naming Rules

Overview

As with all adapters, an existing 2020.1.1500.2 Logic Simulator | Overview is required.

Where to find the different Gateway Adapters.

Where to find

To find the MQTT adapter, go to the Inspector window of a 2020.1.1500.2 Logic Simulator | Overview component.
This 2020.1.1500.2 Logic Simulator | Overview can be added under Logic.

Feature overview

Only the settings between the lines refer to the MQTT Adapter.

Please check the documentation for the rest of the 2020.1.1500.2 Logic Simulator | Overview

Gateway settings

Gateway settings
Adapter Target	Select a different adapter, please see respective documentation for more information
Adapter Setting (MQTTServerSettings)
XmlFilePath	File path to the policy file Warning : <Make sure to fill in a relative path to the Asset folder of the project and include .xml file extension>
ServerName	Is used as the an indicator in the XML policy file
IP Address	The address of the MQTT broker. This can be a be in IPv4 address or a hostname like localhost
Port	The port on which the MQTT broker is running, the default port is 1883
use TLS	Should be turned on when the broker is using TLS authentication. (off by default) Default port for MQTT over TLS is 8883, please check your broker for the correct port
UserName	Is passed to the server for authentication if the field is not empty (not used by default)
PassWord	Is passed to the server for authentication when the UserName field is not empty (not used by default)
QoS	(Quality Of Server) is an agreement between the broker and client that defines the guarantee of delivering a message: 0 : At most once => There is acknowledgement between broker and client other than regular TCP , fast, unreliable (packet loss)) 1 : At least once => The sender buffers the value until a ‘PUBACK’ is returned by the broker. Message can be sent multiple times (, slower, reliable) 2 : Exactly once => The sender sends the message, the broker returns a ‘PUBREC’. The sender is returning a ‘PUBREL’ and the server again returns a ‘PUBCOMP’ command to finalize the sending process. (slow, very reliable) See below for more detail.
Lifecycle settings	Not implemented for MQTT

QoS (Quality of Server) - Detailed agreements

QoS	known as	speed	reliability	remarks

QoS	known as	speed	reliability	remarks
0	fire & forget	fast	poor	Messages can get lost in unstable connections. Very suitable for wires local connection
1	single handshake	slower	good	No message is lost. Can lead to duplicate messages. but is much faster than QoS 2
2	double handshake	slowest	exact	If getting the message exactly once is more important than performance. Quite an overhead compared to the other 2 levels

How to use

Please see the 2020.1.1500.2 Logic Simulator | Overview documentation for further instructions on setting up your simulation.

Prerequisites for MQTT

MQTT can work with an online broker, but is more commonly used with a local broker. There are a lot of brokers available. An overview can be found at: https://en.wikipedia.org/wiki/Comparison_of_MQTT_implementations

ActiveMQ also has an MQTT broker when installed, but feel free to choose one to your liking.

For testing purposes we recommend using a client like i.e. MQTT.fx https://mqttfx.jensd.de/

Used Protocol

To communicate with the MQTT adapter in Prespective you need to apply the following protocol:

The structure for the message is:

<PLCADDRESS/<VALUE>

Topic to write is the address defined by the PLC address in the signal naming
Value is the value that is within the range of the specified type

Supported Types

BOOL
BYTE
SBYTE
WORD
DWORD
SHORT
USHORT
INT16
UINT16
INT32
UINT32
INT64
UINT64
REAL32
REAL64
BYTEARRAY
STRING
STRUCT

Naming Rules

Setting up the component works as like any other prelogic component. The thing you have to take into account is how the PLC Address Path Format (or implicit naming rule) is configured. The output of this Address is the topic to which the component is reading and/or writing.

WARNING : < Make sure both paths are unique >

Each defined input writes the value to the PLC address path topic.

Each defined output reads the value from the PLC address path topic.

The PLC path separator has to be '/'

< Spaces are allowed but not recommended >

A leading '/' is not recommended because it leads to an extra parent topic with id 0.

For an overview of all variables for signal naming, please go to the prelogic component page.